Tag Archives: 62lt

VF Holden Commodore & HSV LS3 6.2lt V8 8.5mm Aeroflow Black Ignition Leads New

February 23, 2024holden62lt, 85mm, aeroflow, black, commodore, holden, ignition, leadsadmin

Aeroflow XPro Xtreme Ignition Products 8.5mm High Performance Black Ignition Leads. Suitable for VF Holden Commodore & HSV LS3 6.2lt V8. Aeroflow has become synonymous with premium quality performance products. Aeroflow’s objective has been to incorporate state-of-the-art manufacturing, aerospace quality materials and rigid quality controls to produce quality performance products at extraordinary value. Aeroflow has taken its forward thinking knowledge to the street, manufacturing a wide range of race quality products to improve street performance and dependability. The Aeroflow 8.5mm XPro Wire is “the” performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of XPro Wire there is only 40 – 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, Aeroflow use a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) “choke”. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Aeroflow’s 8.5mm XPro wire sets have a special helically wound core that has just 40-50 ohms of resistance per foot–but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire features 40 ft. Of tightly wound copper for superior conductivity. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Supplied complete with clip on numbered lead markers. Diameter (mm): 8.50mm. Distributor Terminal Ends: Stock. Distributor Boot Color: Black. Distributor Boot Material: Silicone. Spark Plug Boot Ends: Eight multi-angle. Spark Plug Boot Color: Black. Spark Plug Boot Material: Silicone. Conductor Style: Spiral core. Length: Approximately 8 length end to end. Low resistance: 40-50 ohms per foot. To fit LS3 engine type only. Will not fit any other engine type.

VE Holden Commodore & HSV L98 LS2 LS3 6lt 6.2lt V8 9mm ICE Ignition Leads Black

December 15, 2022holden62lt, black, commodore, holden, ignition, leadsadmin

ICE Ignition is an Australian company that is highly regarded both locally as well as in the highly competitive US market. This is in no small part due to the well-renowned dependability of their products, but also is owing in no small part to the staggering number of winning setups ICE Ignition systems and components have been used on. These include being fitted on winners of the Amsoil Engine Masters Challenge (EMC), numerous US and Australian drag racing vehicles as well as being used on 2 land speed record holding small block LS based Chevs, set at the Bonneville Salt Flats in Utah. The hotter and more powerful the spark – the easier your engine will start. The ultimate 9mm Pro 100 Series wires that are used in these ICE ignition leads are a spiral wound copper alloy core which have an extremely low resistance of just 100 ohms per metre which delivers maximum spark intensity and duration. This results in a better idle and an engine that will run cleaner. Along with the super low resistance of the leads, the ICE Ignition Pro 100 Series Ignition Leads also include the premium quality Snap Lock stainless steel distributor cap which protects the distributor’s internal parts and spark plug fittings. These Snap Lock fittings make installation very easy, and guarantee that the fitment will remain tight even with the huge fluctuations of temperature that is found in virtually every Holden engine bay. To finish off the kit the silicone wire insulation and boots are also able to handle extreme temperature, and are supplied in the kit in a stealthy and attractive black that will suit the style of any engine bay. ICE Ignition 9mm Pro 100 Series Ignition Leads Suitable for VE Holden Commodore & HSV L98 LS2 LS3 6lt 6.2lt V8. ICE Ignition Pro 100 9mm Ignition Leads. Plug wire markers included. Distributor Terminal Ends: To suit coil packs. Distributor Boot Colour: Black. Distributor Boot Material: Silicone. Spark Plug Boot Ends: 180°. Spark Plug Boot Colour: Black. Spark Plug Boot Material: Silicone. Coil Wire Included: Yes. Conductor Style: Spiral Wound Copper Alloy Core. To fit L98, LS2, LS3 engine type only. Will not fit any other engine type. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts & Accessories\Ignition Systems & Components\Ignition Wires & Coil Boots”. The seller is “tuffcarparts” and is located in this country: AU. This item can be shipped worldwide.

Brand: ICE Ignition
MPN: 9GM808-ad
Manufacturer Part Number: 9GM808-ad

VF Holden Commodore & HSV LS3 6.2lt V8 9mm ICE Ignition Performance Leads Black

December 31, 2021holden62lt, black, commodore, holden, ignition, leads, performanceadmin

ICE Ignition 9mm Pro 100 Series Ignition Leads Suitable for VF Holden Commodore & HSV LS3 6.2lt V8. ICE Ignition is an Australian company that is highly regarded both locally as well as in the highly competitive US market. This is in no small part due to the well-renowned dependability of their products, but also is owing in no small part to the staggering number of winning setups ICE Ignition systems and components have been used on. These include being fitted on winners of the Amsoil Engine Masters Challenge (EMC), numerous US and Australian drag racing vehicles as well as being used on 2 land speed record holding small block LS based Chevs, set at the Bonneville Salt Flats in Utah. The hotter and more powerful the spark – the easier your engine will start. The ultimate 9mm Pro 100 Series wires that are used in these ICE ignition leads are a spiral wound copper alloy core which have an extremely low resistance of just 100 ohms per metre which delivers maximum spark intensity and duration. This results in a better idle and an engine that will run cleaner. Along with the super low resistance of the leads, the ICE Ignition Pro 100 Series Ignition Leads also include the premium quality Snap Lock stainless steel distributor cap which protects the distributor’s internal parts and spark plug fittings. These Snap Lock fittings make installation very easy, and guarantee that the fitment will remain tight even with the huge fluctuations of temperature that is found in virtually every Holden engine bay. To finish off the kit the silicone wire insulation and boots are also able to handle extreme temperature, and are supplied in the kit in a stealthy and attractive black that will suit the style of any engine bay. ICE Ignition Pro 100 9mm Ignition Leads. Plug wire markers included. Distributor Terminal Ends: To suit coil packs. Distributor Boot Colour: Black. Distributor Boot Material: Silicone. Spark Plug Boot Ends: 180°. Spark Plug Boot Colour: Black. Spark Plug Boot Material: Silicone. Coil Wire Included: Yes. Conductor Style: Spiral Wound Copper Alloy Core. To fit LS3 engine type only. Will not fit any other engine type. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts & Accessories\Ignition Systems & Components\Ignition Wires & Coil Boots”. The seller is “tuffcarparts” and is located in this country: AU. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Brand: ICE Ignition
Manufacturer Part Number: 9GM808-ae

VF Holden Commodore HSV L77 6lt LS3 6.2lt V8 Aeroflow Ignition Coils Leads Black

February 6, 2021holden62lt, aeroflow, black, coils, commodore, holden, ignition, leadsadmin

Aeroflow High Performance Ignition Coil Set & Aeroflow 8.5mm High Performance Black Ignition Leads Suitable for VF Holden Commodore L77 6 lt LS3 6.2lt V8. This Ignition Upgrade Kit is comprised of top quality parts from Aeroflow Performance. Comprised of an Aeroflow Xpro Xtreme 8.5mm Ignition Lead set and 8 x Aeroflow Xpro High Performance Ignition Coils, this Ignition Upgrade kit is everything your Commodore could ever need. Enjoy the far stronger spark which will aid in delivering a smoother idle, better mid-range power and a flawless engine start, every time. Aeroflow has become synonymous with premium quality performance products. Aeroflow’s objective has been to incorporate state-of-the-art manufacturing, aerospace quality materials and rigid quality controls to produce quality performance products at extraordinary value. Aeroflow has taken its forward thinking knowledge to the street, manufacturing a wide range of race quality products to improve street performance and dependability. Aeroflow Xpro High Performance Ignition Coil Set. Aeroflow now offer a powerful performance upgrade for the L77 & LS3 engines. These coils are a direct bolt-in and are engineered with high quality internal materials and components for coils that will produce higher voltage and spark energy. While b ased on the OEM form for ease of installation, these have been engineered with performance improvements in mind! The internal windings and materials are optimized to boost the spark output and efficiency of the coil resulting in increased performance for your engine. Aeroflow Xpro coils will improve the performance of your vehicle. The E-core dual connector and TFI coils feature epoxy-filled construction and 48,000 maximum volts. They mount directly in place of the factory coil and accept the factory connectors for an easy installation. No tuning or any other changes are required to fit these coils just bolt on, plug in and drive away! Coil Style: Coil pack. Coil Internal Construction: Epoxy. Coil Wire Attachment: Female/Socket. Mounting Bracket Included: No (fits straight to original). Aeroflow XPro Xtreme Ignition Products 8.5mm High Performance Ignition Leads. The Aeroflow 8.5mm XPro Wire is “the” performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of XPro Wire there is only 40 – 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, Aeroflow use a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) “choke”. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Aeroflow’s 8.5mm XPro wire sets have a special helically wound core that has just 40-50 ohms of resistance per foot–but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire features 40 ft. Of tightly wound copper for superior conductivity. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Supplied complete with clip on numbered lead markers. Diameter (mm): 8.50mm. Distributor Terminal Ends: Stock. Distributor Boot Color: Black. Distributor Boot Material: Silicone. Spark Plug Boot Ends: Eight multi-angle. Spark Plug Boot Color: Black. Spark Plug Boot Material: Silicone. Conductor Style: Spiral core. Length: Approximately 8 length end to end. Low resistance: 40-50 ohms per foot. Direct performance replacement for VF Holden Commodore L77 6lt LS3 6.2lt V8. The item “VF Holden Commodore HSV L77 6lt LS3 6.2lt V8 Aeroflow Ignition Coils Leads Black” is in sale since Wednesday, November 4, 2020. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Ignition Systems\Coils, Modules, Pickups”. The seller is “tuffcarparts” and is located in Moorabbin, VIC. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Manufacturer Part Number: AF4020-8265 AF4030-32813-ae
Brand: Aeroflow
Warranty: 1 Year

VF Holden Commodore & HSV LS3 6.2lt V8 8.5mm MSD Performance Ignition Leads New

September 1, 2020holden62lt, 85mm, commodore, holden, ignition, leads, performanceadmin

MSD 8.5mm Super Conductor Ignition Leads Suitable for VF Holden Commodore & HSV LS3 6.2lt V8. The MSD 8.5mm Super Conductor Wire is “the” performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of Super Conductor Wire there is only 40 – 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, MSD use a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) “choke”. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. MSD’s 8.5mm Super Conductor wire sets have a special helically wound core that has just 40-50 ohms of resistance per foot–but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire features 40 ft. Of tightly wound copper for superior conductivity. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Diameter (mm): 8.50mm. Distributor Terminal Ends: Stock. Distributor Boot Color: Grey. Distributor Boot Material: Silicone. Spark Plug Boot Ends: Eight multi-angle. Spark Plug Boot Color: Grey. Spark Plug Boot Material: Silicone. Conductor Style: Spiral core. To fit LS3 engine type only. Will not fit any other engine type. The item “VF Holden Commodore & HSV LS3 6.2lt V8 8.5mm MSD Performance Ignition Leads New” is in sale since Sunday, February 4, 2018. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Ignition Systems\Ignition Wires”. The seller is “tuffcarparts” and is located in Moorabbin, VIC. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Brand: MSD
Manufacturer Part Number: 32819-af

VF V8 Orssom OTR Maf Cold Air Intake Kit Holden Commodore & HSV 6lt & 6.2lt New

March 26, 2020orssom62lt, cold, commodore, holden, intake, orssomadmin

Orssom Performance Genairation4 OTR (Over The Radiator) Cold Air Intake Kit. Suitable for VF V8 6l & 6.2l Holden Commodore & HSV – Retain Maf. POWER, PERFORMANCE & ECONOMY is what is achieved by installing one of these Orssom Performance Cold Air Intakes! No wonder ORSSOM is the VF Holden owners most popular choice when it comes to Over The Radiator Cold Air Intakes. Due to overwhelming sales and popularity of the Orssom Performance Cold Air Intake (Aust reg design No: 315677) to keep up with demand Orssom have recently started manufacturing these intakes out of a premium quality OEM grade injected plastic. Orssom Performance products are NOT vacuum formed or rotational moulded like most cheaper intakes in todays market, which use recycled plastics. Orssom products are made from factory OEM grade plastic material similar to that found in other plastic components under you bonnet. Other inferior grade, competing products over time, will not stand up to the under bonnet temperatures resulting in cracking & distorting, neck areas collapsing, air filters falling out of them until finally they find their way into the rubbish bin. Using a genuine K&N air filter with a huge surface area, the Orssom OTR offers huge flow with perfect filter retention. The filter has an outside width 478mm (18.813″), outside height of 144mm (5.688″) and an outside thickness of 30mm (1.188). Once installed to the vehicle, the filter is retained in a recessed base and is then securely seated by the top cover assembly which is then screwed down. Nothing but cool, clean air will ever get past this air filter! The Orssom OTR kit is specifically designed for the DIY enthusiast and can be fitted using simple hand tools in around 30mins! The package includes the high grade plastic OTR, a K&N panel filter, full fitting kit and we even provide installation instructions! If that’s not enough, a range of helpful videos can be found on the Orssom youtube channel shown below! What you get in this OTR Kit. Genuine K&N Air Filter re-washable (Part No 33-2640). 3 x OTR Mounting Brackets. 2 x 102mm Rubber Bellows. 3 x Speed Clips. 3 x Phillips Head Screws. 1 x 10mm Length Vacuum Breather Hose. 1 x MAFLESS Adapter (Can be used to adapt to MAFLESS at a later date). The benefits of the Orssom Performance intake over the competition are. Due to the wide, beautiful flowing design of the Orssom OTR, you do not need the extra expense of side dress up panels as with other brands. NO laying back of radiator to fit the intake. NO cutting or lengthening of any electrical wires. NO cutting of any body panels to fit intake. NO removing bumper bars to clean or replace air filters. MAF fitment, (Must be fitted with the factory Air Flow Meter). Strong design and internal bracing means this OTR will never crack, deform or let anything past the filter but clean, cool air. Dont let the sleek, Factory appearance of the intake fool you! Immediately upon installing the intake, you will notice the instant throttle response and smoothness in acceleration. You will also notice, you dont have to accelerate as far to get you to the speed you were traveling prior to fitting the intake. Under hard acceleration the intake gives a nice deep, throaty induction sound, just enough to let the guy at the set of lights next to you, know that you have some serious business under the bonnet! Extensive research and development has gone into designing the Orssom Performance Over The Radiator Cold Air Intakes. Be it on road testing, track or on the dyno the following are major proven factors that will be achieved when fitting an Orssom Performance OTRCAI to your vehicle. Cooler air intake temperatures. Increased air flow to your engine. Increase in power and torque. Improvement to your fuel economy. OEM style for that stealth under bonnet appearance. Gains between 3 to 5 mph terminal speed. Up to 1/2 a second off your ET (elapsed time) on the 1/4 mile. Suit VF V8 Commodore & HSV. For V6 or VE options, please see our other listings. Not suitable for VF HSV GTS Models. Designed to retain your standard airflow meter (MAF). Please see our store for MAFLESS version. This kit does not include the airflow meter, you must use your original factory unit. The intake can be installed in around 30 minutes, with the aid of: 7mm & 10mm socket and ratchet, Phillips head and straight blade screw driver, sharp knife or razor blade to trim the hood seal and the fan shroud clips. Easy to follow fitting instructions come in the kit. For further information, please review the installation instructions shown in the images for this listing. Recently poor quality copies of these intakes have surfaced on the market. How to identify a copy. Genuine Orssom Performance Intakes have several distinguishing marks and features on them. You will view these marking shown in our product photo’s listed. Genuine Orssom Performance Intakes are Injected Plastic not Fibreglass. Genuine Orssom Performance Intakes have the Orssom Performance Logo embossed on the Top lids. Genuine Orssom Performance Intake have 2 support braces which are located at the front opening on the Top lid. Tuff Car Parts are a fully authorised ORSSOM dealer and you can be assured of being supplied with a 100% GENUINE ORSSOM intake! Don’t take our word for it though! See just how Orssom these are for yourself at the Orssom youtube channel! A huge range of different installations, induction sound vids and dyno results can be found on the Orssom youtube channel, but here are just a few Orssom samples below! The item “VF V8 Orssom OTR Maf Cold Air Intake Kit Holden Commodore & HSV 6lt & 6.2lt New” is in sale since Sunday, October 13, 2019. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Air Intake, Fuel Delivery\Air Intake Systems”. The seller is “tuffcarparts” and is located in Moorabbin, VIC. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Brand: Orssom Performance
Manufacturer Part Number: VF V8-T

Vf V8 Orssom Otr Mafless Cold Air Intake Kit Holden Commodore & Hsv 6lt & 6.2lt

March 6, 2020orssom62lt, cold, commodore, holden, intake, mafless, orssomadmin

ORSSOM PERFORMANCE GENAIRATION4 OTR (OVER THE RADIATOR) COLD AIR INTAKE KIT. SUITABLE FOR VF V8 6L & 6.2L HOLDEN COMMODORE & HSV – MAFLESS. POWER, PERFORMANCE & ECONOMY is what is achieved by installing one of these Orssom Performance Cold Air Intakes! No wonder ORSSOM is the VF Holden owners most popular choice when it comes to Over The Radiator Cold Air Intakes. Due to overwhelming sales and popularity of the Orssom Performance Cold Air Intake (Aust reg design No: 315677) to keep up with demand Orssom have recently started manufacturing these intakes out of a premium quality OEM grade injected plastic. Orssom Performance products are NOT vacuum formed or rotational moulded like most cheaper intakes in todays market, which use recycled plastics. Orssom products are made from factory OEM grade plastic material similar to that found in other plastic components under you bonnet. Other inferior grade, competing products over time, will not stand up to the under bonnet temperatures resulting in cracking & distorting, neck areas collapsing, air filters falling out of them until finally they find their way into the rubbish bin. Using a genuine K&N air filter with a huge surface area, the Orssom OTR offers huge flow with perfect filter retention. The filter has an outside width 478mm (18.813″), outside height of 144mm (5.688″) and an outside thickness of 30mm (1.188). Once installed to the vehicle, the filter is retained in a recessed base and is then securely seated by the top cover assembly which is then screwed down. Nothing but cool, clean air will ever get past this air filter! The Orssom OTR kit is specifically designed for the DIY enthusiast and can be fitted using simple hand tools in around 30mins! The package includes the high grade plastic OTR, a K&N panel filter, full fitting kit and we even provide installation instructions! If that’s not enough, a range of helpful videos can be found on the Orssom youtube channel shown below! What you get in this OTR Kit. Genuine K&N Air Filter re-washable (Part No 33-2640). 3 x OTR Mounting Brackets. 2 x 102mm Rubber Bellows. 3 x Speed Clips. 3 x Phillips Head Screws. 1 x 10mm Length Vacuum Breather Hose. Intake Air Temp (IAT) Sensor. IAT Sensor wiring extension harness. The benefits of the Orssom Performance intake over the competition are. Due to the wide, beautiful flowing design of the Orssom OTR, you do not need the extra expense of side dress up panels as with other brands. NO laying back of radiator to fit the intake. NO cutting or lengthening of any electrical wires. NO cutting of any body panels to fit intake. NO removing bumper bars to clean or replace air filters. Strong design and internal bracing means this OTR will never crack, deform or let anything past the filter but clean, cool air. Dont let the sleek, Factory appearance of the intake fool you! Immediately upon installing the intake, you will notice the instant throttle response and smoothness in acceleration. You will also notice, you dont have to accelerate as far to get you to the speed you were traveling prior to fitting the intake. Under hard acceleration the intake gives a nice deep, throaty induction sound, just enough to let the guy at the set of lights next to you, know that you have some serious business under the bonnet! Extensive research and development has gone into designing the Orssom Performance Over The Radiator Cold Air Intakes. Be it on road testing, track or on the dyno the following are major proven factors that will be achieved when fitting an Orssom Performance OTRCAI to your vehicle. Cooler air intake temperatures. Increased air flow to your engine. Increase in power and torque. Improvement to your fuel economy. OEM style for that stealth under bonnet appearance. Gains between 3 to 5 mph terminal speed. Up to 1/2 a second off your ET (elapsed time) on the 1/4 mile. Suit VF V8 Commodore & HSV. For V6 or VE options, please see our other listings. Not suitable for VF HSV GTS Models. MAFLESS tune is required. This kit is supplied complete with the Intake Air Temp (IAT) Sensor & wiring extension harness. You will need to drill a hole into the OTR for fitting of this. The intake can be installed in around 30 minutes, with the aid of: 7mm & 10mm socket and ratchet, Phillips head and straight blade screw driver, sharp knife or razor blade to trim the hood seal and the fan shroud clips. Easy to follow fitting instructions come in the kit. For further information, please review the installation instructions shown in the images for this listing. Recently poor quality copies of these intakes have surfaced on the market. How to identify a copy. Genuine Orssom Performance Intakes have several distinguishing marks and features on them. You will view these marking shown in our product photo’s listed. Genuine Orssom Performance Intakes are Injected Plastic not Fibreglass. Genuine Orssom Performance Intakes have the Orssom Performance Logo embossed on the Top lids. Genuine Orssom Performance Intake have 2 support braces which are located at the front opening on the Top lid. Tuff Car Parts are a fully authorised ORSSOM dealer and you can be assured of being supplied with a 100% GENUINE ORSSOM intake! Don’t take our word for it though! See just how Orssom these are for yourself at the Orssom youtube channel! A huge range of different installations, induction sound vids and dyno results can be found on the Orssom youtube channel, but here are just a few Orssom samples below! The item “VF V8 ORSSOM OTR MAFLESS COLD AIR INTAKE KIT HOLDEN COMMODORE & HSV 6LT & 6.2LT” is in sale since Thursday, November 22, 2018. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Air Intake, Fuel Delivery\Air Intake Systems”. The seller is “tuffcarparts” and is located in Moorabbin, VIC. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Brand: Orssom Performance
Manufacturer Part Number: Does Not Apply

VF Holden Commodore & HSV 6lt & 6.2lt V8 Orssom OTR MAF Bundle with Infill Panel

March 3, 2020holden62lt, bundle, commodore, holden, infill, orssom, paneladmin

Orssom Performance Genairation4 OTR (Over The Radiator) Cold Air Intake Kit Full Bundle with OTR Kit & Airbox Infill Panel Suitable for VF V8 6l & 6.2l Holden Commodore & HSV – Retain Maf. POWER, PERFORMANCE & ECONOMY is what is achieved by installing one of these Orssom Performance Cold Air Intakes! No wonder ORSSOM is the VF Holden owners most popular choice when it comes to Over The Radiator Cold Air Intakes. Due to overwhelming sales and popularity of the Orssom Performance Cold Air Intake (Aust reg design No: 315677) to keep up with demand Orssom have recently started manufacturing these intakes out of a premium quality OEM grade injected plastic. Orssom Performance products are NOT vacuum formed or rotational moulded like most cheaper intakes in todays market, which use recycled plastics. Orssom products are made from factory OEM grade plastic material similar to that found in other plastic components under you bonnet. Other inferior grade, competing products over time, will not stand up to the under bonnet temperatures resulting in cracking & distorting, neck areas collapsing, air filters falling out of them until finally they find their way into the rubbish bin. Using a genuine K&N air filter with a huge surface area, the Orssom OTR offers huge flow with perfect filter retention. The filter has an outside width 478mm (18.813″), outside height of 144mm (5.688″) and an outside thickness of 30mm (1.188). Once installed to the vehicle, the filter is retained in a recessed base and is then securely seated by the top cover assembly which is then screwed down. Nothing but cool, clean air will ever get past this air filter! The Orssom OTR kit is specifically designed for the DIY enthusiast and can be fitted using simple hand tools in around 30mins! The package includes the high grade plastic OTR, a K&N panel filter, full fitting kit and we even provide installation instructions! If that’s not enough, a range of helpful videos can be found on the Orssom youtube channel shown below! This bundle also includes an Inner Guard Infill Panel, giving your engine bay that finishing touch! Upon removing your Factory Intake System, you are left with an un-sightly gap exposing the inner plastic wheel arch. What you get in this OTR Kit. Genuine K&N Air Filter re-washable (Part No 33-2640). 3 x OTR Mounting Brackets. 2 x 102mm Rubber Bellows. 3 x Speed Clips. 3 x Phillips Head Screws. 1 x 10mm Length Vacuum Breather Hose. 1 x MAFLESS Adapter (Can be used to adapt to MAFLESS at a later date). The benefits of the Orssom Performance intake over the competition are. Due to the wide, beautiful flowing design of the Orssom OTR, you do not need the extra expense of side dress up panels as with other brands. NO laying back of radiator to fit the intake. NO cutting or lengthening of any electrical wires. NO cutting of any body panels to fit intake. NO removing bumper bars to clean or replace air filters. MAF fitment, (Must be fitted with the factory Air Flow Meter). Strong design and internal bracing means this OTR will never crack, deform or let anything past the filter but clean, cool air. Dont let the sleek, Factory appearance of the intake fool you! Immediately upon installing the intake, you will notice the instant throttle response and smoothness in acceleration. You will also notice, you dont have to accelerate as far to get you to the speed you were traveling prior to fitting the intake. Under hard acceleration the intake gives a nice deep, throaty induction sound, just enough to let the guy at the set of lights next to you, know that you have some serious business under the bonnet! Extensive research and development has gone into designing the Orssom Performance Over The Radiator Cold Air Intakes. Be it on road testing, track or on the dyno the following are major proven factors that will be achieved when fitting an Orssom Performance OTRCAI to your vehicle. Cooler air intake temperatures. Increased air flow to your engine. Increase in power and torque. Improvement to your fuel economy. OEM style for that stealth under bonnet appearance. Gains between 3 to 5 mph terminal speed. Up to 1/2 a second off your ET (elapsed time) on the 1/4 mile. Suit VF V8 Commodore & HSV Series 1. For V6 or VE options, please see our other listings. Not suitable for VF HSV GTS Models. Designed to retain your standard airflow meter (MAF). Please see our store for MAFLESS version. This kit does not include the airflow meter, you must use your original factory unit. The intake can be installed in around 30 minutes, with the aid of: 7mm & 10mm socket and ratchet, Phillips head and straight blade screw driver, sharp knife or razor blade to trim the hood seal and the fan shroud clips. Easy to follow fitting instructions come in the kit. For further information, please review the installation instructions shown in the images for this listing. Please note that as there is some minor variation in this engine bay area in VF Holden & HSV, the infill panels have been made overiszed, so that the panel can then be trimmed down to suit each specific model. Infill Panel will need to be trimmed back to suit your specific vehicle. Sit the Infill Panel in place, line up the fitting points and then measure out how much needs to be cut. Cutting to the Infill Panel can be done with a sharp utility knife etc. Recently poor quality copies of these intakes have surfaced on the market. How to identify a copy. Genuine Orssom Performance Intakes have several distinguishing marks and features on them. You will view these marking shown in our product photo’s listed. Genuine Orssom Performance Intakes are Injected Plastic not Fibreglass. Genuine Orssom Performance Intakes have the Orssom Performance Logo embossed on the Top lids. Genuine Orssom Performance Intake have 2 support braces which are located at the front opening on the Top lid. Tuff Car Parts are a fully authorised ORSSOM dealer and you can be assured of being supplied with a 100% GENUINE ORSSOM intake! Don’t take our word for it though! See just how Orssom these are for yourself at the Orssom youtube channel! A huge range of different installations, induction sound vids and dyno results can be found on the Orssom youtube channel, but here are just a few Orssom samples below! The item “VF Holden Commodore & HSV 6lt & 6.2lt V8 Orssom OTR MAF Bundle with Infill Panel” is in sale since Sunday, October 13, 2019. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Air Intake, Fuel Delivery\Air Intake Systems”. The seller is “tuffcarparts” and is located in Moorabbin, VIC. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Brand: Orssom Performance
Manufacturer Part Number: Does Not Apply

VF Holden Commodore HSV LSA Supercharged V8 6.2lt Cam Package Kit VCM Camshaft

December 12, 2019holden62lt, camshaft, commodore, holden, package, superchargedadmin

CAMSHAFT PACKAGE SUIT LSA 6.2LT SUPERCHARGED V8 VF HOLDEN COMMODORE HSV. Everything you need for a complete LSA Camshaft Package. Using a high quality selection of parts we have been able to put together the LSA Camshaft Package. The Tuff Car Parts LSA Cam Package 1 includes. Any VCM Performance camshaft (full grind list below, please specify in checkout). High quality dual valve spring kit (springs, locks, retainers & seals). 7.400 Chromoly Pushrods. ARP Cam bolt set. Cam package is to fit LSA engine type only. Will not fit any other engine type. The VCM Performance Camshaft range includes 19 separate off-the-shelf grinds (and custom grinds) to suit the LS series of engines including GEN3 5.7lt, and GEN4 6.0lt and 6.2lt. The range includes options for N/A and forced induction applications. VCM Performance has and continues to undertake a rigorous development program with a camshaft range to suit the entire LS engine range. There are 15 grinds available ranging from mild to wild, for naturally aspirated engines, and forced induction applications. All camshaft profiles available will require a retune of the ECU to run correctly. We strongly recommend you discuss your requirements with your tuner/workshop prior to ordering. Our Camshafts are crafted using the highest quality US Billets, and suit the GM LS1, LS2, L76, L98 and LS3 Engines. These are NOT cheap Chinese billets these are high quality USA Billet cams locally ground in Australia in grinds specifically designed for Australian vehicles and conditions. Please note that quoted power figures are indicative only and WILL vary dyno to dyno and day to day. Figures are also dependant on your exact cars setup and parts package. Please refer to the cam chart shown in the images for available choices. The item “VF Holden Commodore HSV LSA Supercharged V8 6.2lt Cam Package Kit VCM Camshaft” is in sale since Thursday, November 22, 2018. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Engines, Components\Camshafts, Lifters & Parts”. The seller is “tuffcarparts” and is located in Moorabbin, VIC. This item can be shipped to Australia, North, South, or Latin America, all countries in Europe, all countries in continental Asia, New Zealand.

Brand: VCM
Manufacturer Part Number: Does Not Apply

November 2024
M	T	W	T	F	S	S
« Oct
				1	2	3
4	5	6	7	8	9	10
11	12	13	14	15	16	17
18	19	20	21	22	23	24
25	26	27	28	29	30